#Profibus_DP
GSD_Revision        = 5
Vendor_Name         = "ChongQing"
Model_Name          = "PDS 8"
Revision            = "1.0"
Ident_Number        =0x0CC2;9701
Protocol_Ident      = 0
Station_Type        = 0
FMS_supp            = 0
Hardware_Release    = "V1.0"
Software_Release    = "V1.0"
31.25_supp          = 1
45.45_supp          = 1
93.75_supp          = 1
MaxTsdr_31.25       = 100
MaxTsdr_45.45       = 250
MaxTsdr_93.75       = 1000
Redundancy          = 0
Repeater_Ctrl_Sig   = 0
24V_Pins            = 0

Freeze_Mode_supp    = 0
Sync_Mode_supp      = 0
Set_Slave_Add_supp  = 1
Min_Slave_Intervall = 250
Modular_Station     = 1
Max_Module          = 2
Max_Input_Len       = 10                    ; maximum Input Length
Max_Output_Len      = 0                     ; maximum Output Length
Max_Data_Len        = 10                    ; maximum In-Output Length
Slave_Family        = 12
Max_Diag_Data_Len   = 20  ;20                
Max_User_Prm_Data_Len = 3
PrmText=1
Text(0)="Disabled"
Text(1)="Enabled"
EndPrmText

ExtUserPrmData=1 "Condensed Status"
Bit(0) 1 0-1 				;PRM_COND
Prm_Text_Ref=1 				;reference to PrmText
EndExtUserPrmData
Ext_User_Prm_Data_Const(0) = 0x00, 0x00, 0x00
Prm_Block_Structure_supp=1				;enables the block structure of extended parameterization



;----------- Description of extended DP features: ---------------------
;
DPV1_Slave = 1
C2_Read_Write_supp      = 1
C2_Max_Data_Len         = 128
C2_Read_Write_required  = 1
C2_Max_Count_Channels   = 2
Max_Initiate_PDU_Length = 52
C2_Response_Timeout     = 4000
DPV1_Data_Types         = 1
Ident_Maintenance_supp  = 1

;--- Description of physical interface for async. and sync. transmission: ---
Physical_Interface = 0                     ; RS-485 Standard Copper
Transmission_Delay_45.45 = 0
Reaction_Delay_45.45     = 0
Transmission_Delay_93.75 = 0
Reaction_Delay_93.75     = 0
End_Physical_Interface
;
Physical_Interface = 1                     ; IEC61158-2
Transmission_Delay_31.25 = 0
Reaction_Delay_31.25     = 0
End_Physical_Interface


;----------- Description of device related diagnosis: ---------------------
;
;Unit_Diag_Bit(16)   = "Error appears"
;Unit_Diag_Bit(17)   = "Error disappears"
;Unit_Diag_Bit(24)   = "Hardware failure electronics"
;Unit_Diag_Bit(25)   = "Hardware failure mechanics"
;Unit_Diag_Bit(26)   = "Motor temperature too high"
;Unit_Diag_Bit(27)   = "Electronic temperature too high"    
;Unit_Diag_Bit(28)   = "Memory error"
;Unit_Diag_Bit(29)   = "Measurement failure"
;Unit_Diag_Bit(30)   = "Device not initialized"
;Unit_Diag_Bit(31)   = "Device initialization failed"
;Unit_Diag_Bit(32)   = "Zero point error"
;Unit_Diag_Bit(33)   = "Power supply failed"
;Unit_Diag_Bit(34)   = "Configuration invalid"
;Unit_Diag_Bit(35)   = "Restart"
Unit_Diag_Bit(36)   = "Coldstart"
;Unit_Diag_Bit(37)   = "Maintenance required"
;Unit_Diag_Bit(38)   = "Characteristics invalid"
;Unit_Diag_Bit(39)   = "Ident_Number violation"
;Unit_Diag_Bit(55)   = "Extension Available"
;Unit_Diag_Bit(56)   = "Diagnostics Cutoff"
;Unit_Diag_Bit(57)   = "Empty Sensor"
;Unit_Diag_Bit(58)   = "Coil Off"
;Unit_Diag_Bit(59)   = "Cable Short"
;Unit_Diag_Bit(60)   = "Volume Flow Low Limit"
;Unit_Diag_Bit(61)   = "Volume Flow High Limit"



;-------------------------------------------------------------------------
;Empty module
Module = "EMPTY_MODULE"                0x00 
1
EndModule
;
;Modules for pressure device
Module   = "AI"                        0x94
2
EndModule
Module   = "AI_EXT"                    0x42,0x84,0x08,0x05
3
EndModule
Module   = "AI1"                        0x94
4
EndModule
Module   = "A1I_EXT"                    0x42,0x84,0x08,0x05
5
EndModule

;----------- Description of the module assignment: ---------------------
;
SlotDefinition
Slot(1) = "AIalog Input 1" 2 1,2,3
Slot(2) = "Analog Input 2" 4 1,4,5
EndSlotDefinition